We may earn money or products from the companies mentioned in this post.
Introduction
Are you a creature of habit when it comes to hunting and gear assortment? While ritualistically checking your Ravin R10 crossbow, you found several issues. Now you’re worried about missing this year’s hunting adventure.
Eager to fix your Ravin R10 crossbow problems?
We have found all the possible problems with the Ravin R10 crossbow. There might be a stiff cocking mechanism problem. But you can easily fix it using a cocking handle. For string issues, you need to check the camera placement. Examine and tighten the stock for accuracy.
Still a little confused?
These were just the problems and solutions in a nutshell. If you’ve got minutes to spare, we have an entire article to help fix your crossbow.
Let’s dive into the details. Shall we?
Possible Problems You May Face With The Ravin R10
Ravin R10 is a hunter’s go-to crossbow for its easy-to-use design and excellent accuracy. It’s safe to say that modern crossbows have a lot of moving parts. Thus they develop problems with gradual use.
Well, you’re in luck with the R10. Because unlike the issues with R9, this model is much easier to fix. We have listed all the possible problems that you might have with your Ravin R10.
Let’s check them out.
Problem 1: Awkward Cocking Mechanism
Ravin R10 has a reverse cocking mechanism. Thus it cocks the crossbow for a even clean shot. However, due to this unique mechanism, you can face issues like clutch slipping.
The built-in cocking system is versatile and integrated into the stock. You might feel annoyed with the clumsy new system. This is because the cocking system is very much near the scope. So, it might get in the way.
Solution
To fix this, you need the proper cocking handle. It is not possible to cock by hand because it cannot be released half-cocked.
Now, for R10, you need a Versa-Draw handle. Here are some recommended Versa-Draw handles that you could use:
| Product 1 | |
| Product 2 |
We can say with confidence that these are top-of-the-line handles for your crossbow.
Now, start by inserting the draw handle into the shaft pins. Then rotate the handle during the de-cocking cycle. At last, slide in the arrow.
Problem 2: String Issues From Defective Cam
Strings are one of the weakest spots of a crossbow. A slight tilt or a hard shove could displace the string. It could prevent you from getting clear shots. In Ravin R10, this issue mainly arises due to the cam.
Solution
Check to see if the cam of your crossbow has started digging into the control cable. Or if it is tilted to the right side. In that case, you can be pretty sure that this is causing the string issues.
For a perfectly functioning crossbow, you should get at least 100 rpm. That too, with good string and maintenance to last you longer.
But, in this case, you’ll have to replace both the cam and the string. You can compare the endless loop and Flemish twist bowstring and choose one. To replace these, you should take help from a professional if you've never done it.
Problem 3: Difficulties While Propping-up
When you’re hunting in a stationary position, it’s safe to have your crossbow propped up. The super-slim profile of R10 and the extra-thin axle-to-axle width make it difficult to prop up.
Then again, while using a crossbow, you must use extreme caution. It always has the risk of toppling over and causing accidents.
Solution
When not in use, you can hang it from a hook or sling. This is easy to maintain and also keeps the crossbow strings safe. You can also install a bubble level to ensure that the crossbow is perfectly vertical.
Plus, this also makes it much easier to prop your bow. Moreover, it might save you a ton of money in case it falls and cracks.
To protect your strings try using limb dampeners and string silencers. You can choose Bowjax or the Limbsaver. These are one of the best ones that’ll keep your crossbow safe!
Problem 4: Stock Fitting
The stock of a crossbow holds the bow bolts and trigger mechanism. So, after shooting around 200 shots, the stock could loosen up. Sometimes it could also have an unsightly seam down the middle.
Solution
In order to fix this, you’ll need to tighten the stock. First, remove all the stock screws and center handle. Then, pull the black rubber cheek-pad off gently. Afterward, separate the stock halves but only halfway.
Now, you’ll need to remove one side of the backing. Then stick the tape on the lower edge. Do this on both lower edges of the split stock halves and at the trigger.
However, you should be careful and not overlap it in any place. Lastly, put the stock half's back together with the glue.
The whole process will take 15 to 25 minutes. To avoid this in the future, you should do proper maintenance and tuning.
That was all! You should keep these in mind when using your R10. Also, properly tune your crossbow to avoid unexpected problems and hunting accidents.
FAQs
Question: Which broadheads should be used for Ravin R10?
Answer: A strong bow like Ravin R10 requires cutting-edge broadheads. Ravin manuals warn us that only company-made accessories should be used. But Grim Reaper 100gr and Muzzy Trocar HBX Hybrid are the best choices.
Question: How long will the strings of a Ravin crossbow last?
Answer: The cables and strings of Ravin are going to last well over 500 shots. The center of the string is the weakest link. So, after 400 shots, Ravin recommends that it be simply replaced.
Question: Does Ravin R10 need nock replacements?
Answer: No, the R10 model has the updated “orange nock” design. Some of the older versions have the “white nock.” There were some technical issues with the white ones. So the company upgraded those with the orange ones.
Final Words
Lastly, we hope that you know what to do about your Ravin R10 Crossbow problems. We’ve tried to cover every possible situation here. But if you’re still facing issues, contact a professional.
We’ll leave you to it. Happy hunting!
