Tru Fire Release Adjustment: 2 Steps to Get the Job Done

We may earn money or products from the companies mentioned in this post.

Introduction

We can understand if you’re confused about bow releases and how to adjust them. You should be confused especially if you’re a newbie to the archery space. Release aids are used to replicate the consistency of releasing the bowstring harder.

Wondering how the tru fire release adjustment is done?

Pay heed to the set screw on the trigger. Rotate the set screw counterclockwise. This should remove the set screw from the trigger. Turning the set screw clockwise will advance the set screw into the trigger, increasing trigger travel. Ensure that you rotate the set screw ¼ turns at a time.

Not satisfied with such little information?  Well, hop in then! We got more detailed information about the topic for you!

True fire could also be worn out pretty quickly. You can check for a better one Amazon. 

Why Should You Adjust Your Tru Fire Release?

Why Should You Adjust Your Tru Fire Release?

While employing one such release, aim for a comfortable grip rather than a firm contact. This must lay comfortably on the bottom of your outstretched hand. The key is to locate that middle ground. 

If you’re confused about how to figure out your sweet spot then it’s okay. Because as a beginner in this space, we’ve all been there and wondered the same. Know that’s the one that’s toe’s the line between convenience and efficiency. 

After finding the sweet spot, remember to mark it. Here, use a marker to indicate that specific spot so that you always shoot from there.

We’ve found just about every other release in Tru Fire's release aid catalog can be lengthened. However, if you’re looking to adjust draw length like Bowtech, you should look at your bow instead. 

The purpose is to strengthen whatever release you have. So that the release jaws are right near the middle joint of your favored trigger finger.

Here’s How You Adjust Your Tru Fire Release’s Trigger Travel

How You Adjust Your Tru Fire Release’s Trigger Travel

First and foremost, it’s critical to realize that Tru Fire has a plethora of releases. Even though they all function similarly, these are all different in their own way. They’re tailored to unique target shooting styles, tastes, and archers.

Necessary Components

  • 1/16th Allen wrench
  • A Tru Fire Release

Now if you’re looking for a 1/16th Allen wrench for your workshop we’ve got a list.

These products that we recommend have been used by us multiple times and tested frequently. We try our best to avoid recommending any faulty products.

Step1: Making Adjustments on the Trigger Travel 

A 1/16 set screw on the grip up adjusts the trigger travel. It's underneath the palm lever. Slide the set screw into the lever clockwise with a 1/16th Allen wrench. This will reduce the trigger travel.

Fret not, if you have no idea what that sentence means; we're here to assist. It simply implies that it would have to travel less distance after firing. Rotating the set screw counterclockwise, on the other hand, would enhance trigger travel.

Step 2: Making Adjustments on the Trigger Tension 

The trigger tension will be the new change we'll need to conduct. Establish where even the trigger emerges from the lever. Solely on a single side of the lever, there are three drilled holes.

If nobody has experimented with the release, it should be positioned at its lowest tension. The screw is situated in the socket adjacent to the − negative symbol. This exact socket site will weigh approximately 6 ounces. The center bit would be 24 ounces, even though the last hole (+) will be roughly 50 ounces.

You don’t need to do much to advance from the 6-ounce level to the 24-ounce. Merely loosen the screw from its previous spot and insert it into the center socket. As soon as you withdraw the screw from the initial hole, re-adjust your trigger travel. 

We’ve covered everything there’s to know on trigger travel adjustment. As you keep practicing you’ll eventually discover better release techniques. Read on to learn more on release adjustment.

Here’s How You Adjust Your Tru Fire Release’s Trigger Tension

Hold your release in your wrist and position the head to the side towards you. Now, to reduce trigger tension, rotate the tension dial right to left. Raise the trigger tension by turning the tension lever to the left or counterclockwise. This gauge only adjusts trigger pressure and no trigger travel.

N.B. After you've adjusted your release, put it through its paces on something other than your bow. Use an old bowstring, insulated wire, or a rubber band. Use anything that can withstand the same level of strain as your bow's pull load.Avoid deflecting any release back at your forehead. You shouldn't be doing so in order to avoid accidentally discharging the trigger. When pulling back, make sure you have an arrow in your bow.Also, try to keep the target within a few meters of you. This will serve as a good stopgap measure. Failure to take these precautions may lead to serious harm to you or another person. 

A properly configured tru fire adjustment should help you fire arrows more precisely. Thanks to this your chances of difficulties with arrow flight will decrease significantly.

FAQs

Question: When it comes to archery, how tight should a release be?

Answer: It should be snug enough to halt at the palm of your hand. It really should work as intended you draw your string to dock. This should not, nevertheless, be so restrictive that it is painful or cuts off flow. 

Question: With a wrist release, where do you anchor?

Answer: Place the index finger precisely at the bottom of the earlobe with a forearm release. This posture enables you to settle in the very same spot every time, maintaining continuity.

Question: What is the best way to secure a bowstring?

Answer: A kisser hook that wraps over the recurve bow is a popular attachment. tAnd it might assist you in creating an anchor point. Simply press the kisser key in the bottom of your lips to return to the same origin point.

Final Words

Now you probably have a good idea regarding the tru fire release adjustment. As you progress you’ll learn new and more improved techniques. But for now, be happy with what you’ve learned today because it’s going to help you loads. 

Good luck with archery. May Apollo’s light shine upon you!

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top